LG Washer Error Code UE — Unbalanced Load
uE means the washer is still trying to rebalance on its own — give it a few minutes. Capital UE means it tried, failed, and needs your help.)What the code means
Before and during spin, the washer checks whether the load is balanced. If laundry has bunched to one side, the machine first tries to fix it itself — tumbling or adding water to redistribute the load — and shows a lowercase uE while it works. LG's top-load guidance puts that at up to three attempts (the unwinding motion can add about 10 minutes). If the load still will not balance, the cycle pauses and the display switches to capital UE. The machine is protecting itself and your floor: a heavy, off-center load at full spin speed shakes violently and can damage the tub, suspension, and the washer itself.
Likely causes, in the order to check them
- Laundry piled or tangled on one side (most common). Sheets and towels ball up around other items; a single heavy item — a comforter, bath mat, or blanket soaked with water — pulls the whole load off-center.
- Load too small. One towel, one pair of jeans, or one knitted item packs to one side and cannot spread out. LG advises washing at least two similar items together and adding one or two items to a very small load.
- Load too large, or the wrong cycle for bulky items. An overfilled drum cannot redistribute. LG advises using the bulky/large (or blanket/duvet) cycle for rugs, comforters, sheets, blankets, and pillows, and washing bulky items one at a time.
- A laundry net used wrong. A lone net, or a net filled past about two-thirds, unbalances the tub. Fill nets only to two-thirds and wash them with other clothes.
- Washer not level. If the machine rocks, the tub swings off-center even with a good load. All four feet should sit firmly on the floor.
- On a brand-new washer: shipping bolts still installed. Front-loaders ship with bolts locking the tub. If they were never removed, the washer shakes and throws balance codes from the first load.
- Worn suspension (repeat UE only, least common). If UE returns on normal, balanced loads in a level machine, worn suspension rods (top-load) or shock absorbers (front-load) can let the tub move too much. That is a diagnosis, not a first guess — see "When to call a pro."
Step-by-step fix
- If you see lowercase
uE, wait. The washer is rebalancing on its own. Do not open the door — that resets its attempt. Give it several minutes. - Pause, open, and redistribute. Separate tangled items, untwist sheets, and spread everything evenly around the drum. Break up any single heavy ball of laundry.
- Fix the load size — aim for about two-thirds full. LG states the washer performs best when the load is about 2/3 of drum capacity. Too small: add one or two similar items. Too big: take a few items out. Single heavy item: add a few towels to balance it, or wash it alone on the bulky cycle at a lower spin speed.
- Restart the cycle (a spin or rinse-and-spin cycle is fine for testing). On small loads, LG suggests reducing spin speed to low or no spin if UE keeps triggering.
- Check the level. Rock the washer gently corner to corner — it should not move. Put a level on top, front-to-back and side-to-side, and adjust the leveling legs until the bubble centers and all four feet are firm, then tighten the lock nuts if your model has them.
- New install? Check the shipping bolts. Look at the back panel: if the shipping bolts are still in place, remove them per your model's manual and plug the holes with the caps provided. Never run a front-loader with the bolts in.
- Run the empty test if UE keeps coming back. Run a rinse-and-spin with an empty drum. An empty drum should never be unbalanced — if UE (or heavy shaking) appears with nothing in the machine, the problem is mechanical, not laundry. Stop there and see below.
The part involved
UE normally involves no replacement part — it is a load and setup code, and this page deliberately does not sell you one. A part only enters the picture when UE repeats on balanced, correctly sized loads in a level machine, or fires on an empty drum: then the suspects are the suspension system (rods on top-load models, shock absorbers on front-load models) or, less often, the sensor that reports drum speed. Those parts vary by model and the symptoms overlap, so confirm the diagnosis — and your model number — before ordering anything.
No part is recommended for a first UE code. If a technician confirms worn suspension parts for your model, buy links for PartSelect and RepairClinic will appear here once our affiliate accounts are active. Until then, search your model number at your preferred parts retailer and verify fit before ordering.
Difficulty and cost picture
Redistributing and resizing the load: free, a few minutes. Leveling: easy, a wrench and a level, about 15 minutes. Suspension work is a moderate-to-advanced job inside the cabinet; published 2026 repair guides put professional suspension replacement in the low-to-mid hundreds (parts and labor), which is why the free checks — and the empty-drum test — come first.
When to call a pro
- UE appears on an empty drum, or on every load no matter how carefully you balance it.
- The washer walks, bangs, or shakes violently even after leveling.
- UE returns after you have confirmed the load, the level, and (on a new machine) the shipping bolts.
- You can see a broken or detached suspension spring, rod, or shock absorber.
Drain problem instead? See the LG OE (drain error) guide. Filling problem? See the LG IE (water inlet error) guide.
Sources
- LG's own UE definition and causes (laundry piled on one side; load too large or too small; washer not level), the two-thirds drum guidance, redistribution steps, and laundry-net guidance — LG USA Support, "LG Front Load Washer — Error Code List (New)" (lg.com). Checked November 2026.
- Lowercase uE vs. capital UE, three rebalance attempts, manual redistribution, adding items, low/no spin on small loads, and bulky-cycle guidance — LG USA Support, "UE Error Code — Washing Machine" (top-load UE/Ub) (lg.com). Checked November 2026.
- Small-load packing behavior and the ~10-minute unwinding motion — LG Support, "UE error code — Unbalanced load [top load washer]" (lg.com). Checked November 2026.
- Repeat-UE mechanical causes (worn suspension rods/shock absorbers, shipping bolts on new installs) — A&Y Appliances, "LG Washer Error Codes"; HowToFixIt, "LG Washer UE Error Code." Checked November 2026.
Some links on this page may become affiliate links; see our affiliate disclosure. FixCode HQ is not affiliated with LG.