Samsung Washer Error Code 5C — No Drain
nd, 5E, SE, SC, or 1 5C on other Samsung models. Samsung says incorrect drain hose installation is the most common reason for drain problems, so check the hose position first, then the pump filter on a front-loader. Most 5C codes clear with no part at all.What the code means
At the drain step, the washer runs its drain pump and watches the water level fall. If the level does not drop at the expected speed — or does not drop at all — the cycle stops and the display shows the no-drain code. Samsung groups six spellings into this one fault: 5C on newer models, and nd, 5E, SE, SC, and 1 5C on others. They all mean the same thing and take the same checks. The washer is not necessarily broken: anything that slows the water on its way out — a kinked hose, a hose pushed too deep, a clogged filter — produces this code.
Likely causes, in the order to check them
- Drain hose installed wrong (most common). Samsung names this the most common reason for drain issues. The hose must sit 6 to 8 inches into the standpipe or sink — deeper can siphon or block flow — be secured so it cannot slip farther down, and must not form an airtight seal.
- Drain hose kinked, clogged, or frozen. A hose pinched behind the washer after a move, lint and debris built up inside it, or a frozen section in a cold laundry room all slow the drain to a crawl.
- Clogged pump filter (front-loaders). Coins, lint, and small items collect in the debris filter ahead of the pump. A packed filter is the classic front-load 5C. Top-loaders have no owner-removable pump filter — skip this cause on a top-load model.
- Drain hose at the wrong height. The drain must be at least 18 inches high (24 inches for a wash basin) and no higher than 96 inches (35 inches for a wash basin). Too low and water siphons out mid-cycle; too high and the pump cannot push water up and over.
- Washer not level. Samsung notes a washer that is not level may not drain correctly.
- Drain hose extension kit fitted. Samsung's guidance is not to use one — extensions add length and restriction the pump was not sized for.
- Failed drain pump (least common, last suspect). Only after the hose, filter, height, and level check out: a pump that hums but moves no water, or stays silent, has likely failed or is jammed with debris that reached it.
Step-by-step fix
- Turn the washer off and check the level. Rock the machine gently corner to corner — it should not move. Adjust the leveling legs until all four feet sit firm.
- Inspect the drain hose end to end. Straighten any kink, look for damage or a clog, and check for a frozen section if the room is cold. Confirm there is no extension kit in the run.
- Set the hose position to Samsung's numbers. Insert the hose 6 to 8 inches into the standpipe or sink — no less, no more — secure it so it cannot slip deeper, and leave the connection loose enough that it is not airtight. Confirm the drain point is at least 18 inches high (24 inches for a wash basin) and no higher than 96 inches (35 inches for a basin).
- Front-loaders: clean the pump filter. With the washer unplugged, open the small access panel at the lower front, drain the residual water through the small hose into a shallow pan, then unscrew the filter, clear out coins, lint, and debris, rinse it, and refit it snugly. Top-loaders do not have this filter — do not go looking for one.
- Run a test cycle. Turn the washer back on and start a cycle (rinse and spin is a good test). Samsung's check: the washer should drain at the beginning of the test cycle.
- If it still will not drain, stop. With the hose, filter, height, and level all verified, Samsung's own guidance is to request service — the drain pump is the remaining suspect, and it is a diagnosis to confirm, not a part to guess.
The part involved
If every check above passes and the washer still will not drain, the part is the drain pump. Unlike some brands, Samsung does not use one pump across its washer lines — the correct pump varies by model, and ordering by code alone will get you the wrong part. Confirm your model number first, then match the pump to that model. A pump that hums with no water movement is usually jammed or failed; a silent pump can also be a wiring or control fault, which is why a confirmed diagnosis beats a guess.
Samsung drain pumps are model-specific — there is no single part number for a 5C code. Buy links for PartSelect and RepairClinic will appear here once our affiliate accounts are active, and they will be organized by model lookup, not by a one-size part. Until then, search your exact model number at your preferred parts retailer and verify the pump fits that model before ordering.
Difficulty and cost picture
Hose repositioning and leveling: free, a few minutes, no tools beyond maybe a wrench for the legs. Filter cleaning: easy, about 15 minutes, towels and a pan. Drain pump replacement is a moderate job inside the cabinet, and because the part is model-specific, professional diagnosis first is money well spent if the free checks did not clear the code.
When to call a pro
- The washer does not drain at the start of a test cycle after the hose, filter, height, and level are all verified — Samsung's own service line.
- The pump is silent, or hums but moves no water, with a clear filter and a correct hose.
- Water leaks from the pump or filter housing while draining.
- The 5C code returns immediately on every cycle, even with an empty drum.
Unbalanced load instead? That is a different code family — see the LG UE guide for how balance codes behave, and watch for the Samsung hub page as this brand's library builds out. Drain problem on an LG? See the LG OE (drain error) guide.
Sources
- The 5C code group (nd, 5E, SE, 5C, SC, 1 5C) defined as the no-drain error — water not draining at the correct speed, or at all — with the level, hose, and pump-filter checks — Samsung Support, "Samsung Washing Machine Information and Error Codes" (samsung.com). Checked November 2026.
- Incorrect drain hose installation as the most common drain cause; hose inserted 6 to 8 inches, secured, not airtight; drain height at least 18 inches (24 for wash basins) and no higher than 96 inches (35 for basins); no extension kit; pump filter is front-load only; test-cycle drain check and the request-service line — Samsung US Support, "Samsung washing machine will not drain" (samsung.com). Checked November 2026.
Some links on this page may become affiliate links; see our affiliate disclosure. FixCode HQ is not affiliated with Samsung.